跳至主要内容

【转】u盘驱动过程（linux－2.6.24）

标签：u盘 驱动 过程 　　　[推送到技术圈]

版权声明：原创作品，允许转载，转载时请务必以超链接形式标明文章 原始出处 、作者信息和本声明。否则将追究法律责任。http://ironpeak.blog.51cto.com/439173/100490
u盘驱动过程（linux－2.6.24）

第一次编译出的问题：
[root@/]#usb 1-1: new full speed USB device using s3c2410-ohci and address 4    
usb 1-1: device descriptor read/64, error -62                                   
usb 1-1: device descriptor read/64, error -62                                   
usb 1-1: new full speed USB device using s3c2410-ohci and address 5             
usb 1-1: device descriptor read/64, error -62                                   
usb 1-1: configuration #1 chosen from 1 choice

解决办法：

去掉了        Device Drivers   －－》
            <*> Real Time Clock 前的＊

第二次编译出现问题：
插入u盘时的显示：
[root@/]#usb 1-1: new full speed USB device using s3c2410-ohci and address 3    
                                                                                
usb 1-1: configuration #1 chosen from 1 choice                                 
                                                                               
scsi1 : SCSI emulation for USB Mass Storage devices                            
                                                                               
scsi 1:0:0:0: Direct-Access     Kingston DataTraveler2.0  1.00 PQ: 0 ANSI: 2   
                                                                               
sd 1:0:0:0: [sda] 3903359 512-byte hardware sectors (1999 MB)                  
                                                                               
sd 1:0:0:0: [sda] Write Protect is off                                         
                                                                               
sd 1:0:0:0: [sda] Assuming drive cache: write through                          
                                                                               
sd 1:0:0:0: [sda] 3903359 512-byte hardware sectors (1999 MB)                  
                                                                               
sd 1:0:0:0: [sda] Write Protect is off                                         
                                                                               
sd 1:0:0:0: [sda] Assuming drive cache: write through                          
                                                                               
 sda: sda1                                                                     
                                                                               
sd 1:0:0:0: [sda] Attached SCSI removable disk
看似没有问题，但是在挂载的时候出现问题：
Unable to load NLS charset  cp437
FAT: codepage cp437 not found

解决办法：
在File systems－－》
                Native language support－－》
                    <*>   Codepage 437 (United States, Canada)    添加＊


第三次编译出现问题：

插入后显示和第二次一样;
挂载的时候出现问题：
Unable to load NLS charset iso8859-1                                           
                                                                               
FAT: IO charset iso8859-1 not found

解决办法：
在File systems－－》
                Native language support－－》
                    <*>   NLS ISO 8859-1  (Latin 1; Western European Languages)         添加＊

第三次编译成功挂在u盘！！！


问题补充：

如果出现以下问题：
usb 1-1: device descriptor read/64, error -110


解决办法：
修改linux-2.6.24/drivers/usb/host/ohci-s3c2410.c

添加头文件：
#include <asm/arch/regs-clock.h>

在s3c2410_start_hc里增加：

unsigned long upllvalue = (0x78<<12)|(0x02<<4)|(0x03);

while (upllvalue != __raw_readl(S3C2410_UPLLCON))
{
__raw_writel(upllvalue, S3C2410_UPLLCON);
mdelay(1);
}

本文出自 "西安铁峰电子有限公司" 博客，请务必保留此出处http://ironpeak.blog.51cto.com/439173/100490

评论

发表评论

此博客中的热门博文

【转】smb协议栈使用示例

/*  * * uncdownload.c  * *  * * Utility for downloading files from SMB shares using libsmbclient  * *  * * Copyright(C) 2006 Sophos Plc, Oxford, England.  * *  * * This program is free software; you can redistribute it and/or modify it under the terms of the  * * GNU General Public License Version 2 as published by the Free Software Foundation.  * *  * * This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without  * * even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  * * See the GNU General Public License for more details.  * *  * * You should have received a copy of the GNU General Public License along with this program; if not,  * * write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA  * *  * */ # include < sys / types . h > # include < sys / time . h > # include ...
发表评论
阅读全文

【转】Ether Types

Ether Types (last updated 2008-09-09) NOTE: Please see [RFC5342] for current information and registration procedures. This registry will be revised soon and will be replaced with up-to-date information. Many of the networks of all classes are Ethernets (10Mb) or Experimental Ethernets (3Mb). These systems use a message "type" field in much the same way the ARPANET uses the "link" field. If you need an Ether Type, contact: IEEE Registration Authority IEEE Standards Department 445 Hoes Lane Piscataway, NJ 08854 Phone +1 732 562 3813 Fax: +1 732 562 1571 Email: <ieee-registration-authority& ieee.org > http://standards.ieee.org/regauth/index.html The following list of EtherTypes is contributed unverified information from various sources. Another list of EtherTypes is maintained by Michael A. Patton and is accessible at: <URL: http://www.cavebear.com/CaveBear/Ethernet/ > <URL: ftp://ftp.cavebear.com/pub/Ethernet-codes > Assign...
发表评论
阅读全文

【转】移植Linux的应用软件到Windows

一．前言  　　 Linux 拥有丰富各种源代码资源,但是大部分代码在 Windows 平台情况是无法正常编译的。 Windows 平台根本无法直接利用这些源代码资源。如果想要使用完整的代码，就要做移植工作。因为C/C++ Library的不同和其他的一些原因，移植C/C++代码是一项困难的工作。本文将以一个实际的例子（Tar）来说明如何把 Linux 代码移植到 Windows 平台上。移植过程将尽量少修改代码,以便代码的运行逻辑不会发生任何变动。保留绝大部分软件主要功能。  　　二．准备工作  　　Tar是 Linux 平台下面一个打包工具。移植这样一个程序到 Windows 平台需要做那些工作呢？  　　首先是一些准备工作，在 Windows 平台上面安装上Cygwin的最新版本，在Cygwin中安装好GCC等开发工具。 同样也需要一个 Windows 开发环境。可以使用最新版本Visual Studio, Microsoft Visual Studio .NET 2003。从 www.gnu.org 上取得Tar的最新源代码，版本是1.13。在Cygwin下面解开tar-1.13.tar.gz.源代码包。注意请不要在 Windows 下面使用WINRAR或者WINZIP来解压缩。 WINRAR和WINZIP在解压缩某些tar.gz包的时候会有问题。使得解包之后的目录和文件出现异常。如果是源代码包将有可能不能在Cygwin下面正确编译。解开压缩包之后，进入 tar-1.13目录，在当前的目录下面输入./configure命令，运行完毕之后，再次输入make命令。开始编译tar的Cygwin版本。编译基本上不会有问题，进入src目录，可以看到新编译好的Tar程序tar.exe。  　　Cygwin是一个API层的 Linux 模拟环境。如果能够在Cygwin下面编译，运行。实际上也就是能在 Windows 下面编译和运行，只是需要有一层中间API模拟某些 Linux 特有的操作。简单的判断一个 Linux 程序能不能移植到 Windows 平台下面，就是看是否能在Cygwin下面编译源代码，并运行程序。...
发表评论
阅读全文